Service
Water damage drywall replacement in Fairhope after storms and leaks
Water damage drywall replacement in Fairhope usually turns on one question, and we answer it with a meter rather than a guess: how far did the water travel inside the wall or ceiling? The stain on the surface is the part you can see. Gypsum wicks water upward and sideways well past that line, and the studs, insulation and bottom plate behind it can hold moisture for days after the paint feels dry.
This page covers what we check, where we cut, and how the wall goes back together, whether the water came from a tropical storm, a roof leak or a supply line that let go under a sink.
Mapping
Measure how far the water went
We start outside the damage and work in. A scanning meter slid along the wall finds the wet zone without marking the paint, and a pin meter confirms the readings at the board itself and, where a hole is already open, in the stud. Readings get marked on painter's tape at the edge of the wet area, so the cut line follows the moisture, not the stain.
We also check the rooms on the other side of the wall and the ceiling below any upstairs leak. Water runs along the top of a bottom plate and can show up in a closet or the next room before it shows where it started.
Storm season
Plan for the next tropical storm
Baldwin County sits on the Gulf and sees tropical weather often. Hurricane Sally, which came ashore at Gulf Shores on September 16, 2020 as a strong Category 2 storm, showed what that can mean for walls. The National Weather Service office in Mobile recorded Sally moving at under 5 mph at landfall, and the slow crawl left 15 to 30 inches of rain across the county. A gauge just outside Fairhope logged 12.44 inches.
Rain like that gets in through places that stay dry in an ordinary storm: window flashing, soffit vents, the gap under an exterior door. After a long blow off the bay, check the inside of exterior walls at window corners and along the baseboard, and look up at ceilings under roof valleys. Damage that shows up a week later is often from the storm, not something new.
Cutting
Cut back to dry, sound board
Wet gypsum loses strength, and paper-faced board that stays damp can start growing mold on the back side where you can't see it. Board that is soft, bowed or still reading wet after a few days of drying comes out. We cut in straight, level lines, usually breaking at the center of a stud so both edges of the replacement land on wood for screwing.
For water that rose from the floor, the cut goes above the highest wet reading, commonly two or four feet up so it lines up with standard sheet widths. Wet insulation behind it comes out too. Once the wall is open we check the studs and bottom plate, run fans and a dehumidifier, and wait for the framing to read dry before closing it. In our humid air, that wait is the part that can't be rushed.
Supply leaks
Shut off the right valve first
For a supply-line leak, the fixture valve under the sink or behind the toilet is the first stop. If a pipe inside the wall is the problem, the house main has to be closed. Fairhope runs its own water and sewer service through Fairhope Public Utilities, so a leak on the city side of the meter is theirs to look at; anything on the house side needs a plumber. We open the wall and rebuild it, but the pipe repair comes first.
Rebuilding
Rebuild the wall in layers
New board matches the thickness of what came out, so the face of the wall stays flat. In bathrooms and laundry rooms we use moisture-resistant board, and on the wall between the garage and the house, fire-rated board to match what was there. Joints get paper tape bedded in compound, then fill and finish coats feathered wide, then a primer that seals the new paper and the old wall alike.
If the surrounding wall has texture, the patch gets the same texture before primer. Paint can be included or left to your painter; either way, the wall is ready for it.
FAQ
Get answers about wet drywall
Can wet drywall dry out and stay in place?
Sometimes. If the board got wet briefly, dries back to normal readings within a few days and is still firm with the paper still stuck tight, a coat of stain-blocking primer and then paint is usually enough. If it stayed wet longer, sags, or crumbles when pressed, it should come out.
How high up the wall do you cut after water comes in at floor level?
Above the highest wet reading, not the visible stain. That often lands at two or four feet so the new piece matches standard sheet sizes, but the readings decide it.
Does the water need to be off before you arrive?
The leak needs to be stopped, yes. If the pipe or roof is still letting water in, any new board will get wet again, so the plumbing or roofing repair comes first.
Related
Look at related repairs
Water that came through the roof usually shows on a ceiling first; the page on tracing and repairing ceiling stains covers that side. Tape that lifted after a leak dried out is a separate fix, explained under seam and crack repair. To see whether your town is on our route, check the Eastern Shore towns we cover, or describe the water damage to us. Deciding between a patch and a full sheet? Read our patch-or-replace guide.
Next step
Book a moisture check for this wall
Phone the shop, text over a picture, or fill in the contact page. Say where the damage is and what you think started it.
Open 7 days, 7am–9pm
Text a photo any time to the same number; it is read during open hours.