Fairhope Drywall Repair Pros (251) 270-4751Open 7 days, 7am–9pm

Service

Drywall hole patching for Fairhope homes and rentals

Drywall hole patching in Fairhope covers everything from a row of picture-hanger holes to a break you could push a fist through. The method changes with the size, so the first thing we do is measure the damage and check what sits behind it.

Size

Size the hole before choosing a patch

DamageWhat it usually takes
Nail and anchor holes, under half an inchFill with lightweight compound, two thin passes, sand and prime.
Dents and holes up to about 4 inchesTrim loose paper, mesh or a paper-backed patch, three feathered coats.
Holes about 4 to 8 inches, like a doorknob breakCut to a square, add wood or metal backing, screw in a new piece, tape all four sides.
Larger than a hand span, or crossing a studCut back to the nearest studs and set a full-height or partial-sheet piece.

Doorknob holes are the most common break we see, nearly always on the wall behind a door with no stop. A patch there is worth pairing with a door stop, or the knob will find the same spot.

Behind the wall

Check what sits behind the hole

Before cutting a hole larger, we look inside with a light and check for wiring, pipes and duct runs. Outlets and switches mark where cable runs; a hole low on a bathroom or kitchen wall may sit right over a supply line. Cuts are kept shallow and, near anything live, made by hand.

In older houses, like the remodeled cottages in the Montrose Historic District, we also check what the wall is made of. Some walls there are drywall laid over older material, and a patch has to match the full thickness, not just the face layer. In the Fairhope Bayfront District, decades of remodeling can mean two thicknesses of board in one room, so the edge of the opening gets measured before a piece is cut.

Layers

See what goes inside a good patch

Cross-section of a backed drywall patch A side view through a wall. The old board sits on both sides, a new piece fills the gap between them, a wood backing strip behind spans the joints, screws hold it, tape bridges each joint on the face, and three coats of compound spread progressively wider over the tape. Three coats, each wider Tape over each joint Existing board Wood backing strip behind New piece, same thickness Screws into backing
The backing holds the new piece flush; the widening coats hide the slight rise of the tape.

A patch is a small piece of wall rebuilt in layers. Backing holds the new piece flush. Screws fix it to the backing without breaking the paper. Tape bridges the seams so they don't crack later. Then three coats of compound, each one wider than the one before, spread the slight hump of the tape over a wide enough area that the eye can't find it.

On muggy days we use setting-type compound for the first coat. It cures chemically instead of air-drying, so humid air on this side of Mobile Bay doesn't hold the job up between coats.

Finish

Blend the patch into the wall

The finish decides whether a patch disappears. We inspect the patch under a lamp angled low beside the wall, sand any ridge, and rebuild texture if the wall has it. Primer goes over the whole repair so the new compound doesn't absorb paint differently from the old surface. When painting is in the scope, we paint corner to corner rather than just over the patch, since a spot of fresh paint on an older wall shows even when the color is the same.

Landlords turning over a unit can send the whole list of holes at once; patching several rooms in one visit is how most rental work gets done.

FAQ

Settle the usual patching questions

Will the patch show once it's painted?

Not when the coats are feathered wide and the whole wall section is primed and painted. Painting only the patch itself is what usually makes a repair visible.

Can you patch a hole right next to an outlet?

Yes. With the power to that circuit off and the cover plate removed, the patch can be fitted around the box so the cover sits flat again afterward.

Do I need to paint the whole wall afterward?

For the repair to disappear, painting from corner to corner works best. A small touch-up can blend if the existing paint is fresh and the same batch is on hand.

Related

Look at the other wall repairs

A hole that came with cracks spreading out from it may need tape and crack work as well. If the board around the hole is soft or stained, it is a moisture problem first, covered under replacing wet drywall. Our guide on when to patch and when to replace helps with the bigger breaks. See where we take patching jobs, or send the list of holes.

Next step

Book a moisture check for this wall

Phone the shop, text over a picture, or fill in the contact page. Say where the damage is and what you think started it.

(251) 270-4751

Open 7 days, 7am–9pm

Text a photo any time to the same number; it is read during open hours.